A-PAMDrag to rotate
Polymer segmentCNONaH
Industrial chemicals

Anionic Polyacrylamide (Flocculant)

Low to high charge, high MW

CAS 25085-02-3HS 3906.90
Product family
Chemicals
Forms
PowderEmulsion
Packaging
25 kg bags1,000 L IBC
Request TDS / MSDS

What is anionic polyacrylamide?

Anionic polyacrylamide (APAM) is a water-soluble, very high-molecular-weight copolymer of acrylamide and sodium acrylate (CAS 25085-02-3). Its long, negatively charged chains bridge fine particles into large flocs that settle or drain quickly.

APAM is sold by anionic charge (about 5–50 %) and molecular weight (typically 10–25 million g/mol), as granular powder or as liquid emulsion. The right grade is chosen by jar or cylinder tests on the user’s own slurry or water.

Where is anionic polyacrylamide used?

APAM is the standard flocculant in mining thickeners and tailings, and it is widely used in water and wastewater treatment, coal and sand washing, paper making and oilfield water. It is usually dosed after a coagulant such as PAC or ferric chloride.

How is APAM produced?

Acrylamide monomer, today made mostly by enzymatic hydration of acrylonitrile, is copolymerised with acrylic acid or sodium acrylate. The ratio of the two monomers sets the anionic charge.

  • Powder: gel polymerisation in water, then cutting, drying and milling to free-flowing granules.
  • Emulsion: inverse-emulsion polymerisation, giving polymer droplets in oil that dissolve within minutes when mixed with water.
  • Each lot is tested for solids, charge, viscosity (a measure of molecular weight), dissolution time, insolubles and residual acrylamide.

APAM grades and forms

The table compares the main grades and forms; each is then explained with its typical uses.

Low anionicMedium anionicHigh anionicEmulsion
Anionic charge5–15 %20–30 %35–50 %10–40 %
Molecular weightHighHigh to very highVery highHigh
Active content≥ 88 %≥ 88 %≥ 88 %about 30–50 %
Best forDrinking water, acidic slurriesThickeners, tailings, coalAlkaline slurries, high-pH tailingsFast make-down, inline dosing

Low-anionic APAM (5–15 %)

Lower charge suits neutral to acidic conditions and gives clear overflows. Drinking-water grades with low residual monomer are available.

Typical uses
  • Drinking-water and surface-water clarification
  • Acidic leach slurries and CCD circuits
  • Paper and process-water clarification

Medium-anionic APAM (20–30 %)

The most widely used range for mineral slurries, balancing settling speed and overflow clarity.

Typical uses
  • Concentrate and tailings thickeners
  • Coal, sand and aggregate washing
  • Paste and high-density tailings

High-anionic APAM (35–50 %)

Higher charge and molecular weight extend the polymer chains in alkaline, high-ionic slurries.

Typical uses
  • Alkaline tailings and red mud
  • High-pH process water
  • Industrial effluents with metal hydroxides

APAM emulsion

Liquid polymer in oil, about 30–50 % active. It dissolves in minutes and suits sites without a powder make-up unit.

Typical uses
  • Inline and mobile dosing
  • Oilfield and produced-water treatment
  • Temporary or seasonal plants

Typical analysis (powder)

ParameterTypical value
AppearanceWhite to off-white granular powder
Solid content≥ 88 %
Anionic charge5–50 % (per grade)
Molecular weightabout 10–25 million g/mol
Residual acrylamide≤ 0.05 % (drinking-water grade ≤ 0.025 %)
Dissolution time (0.1 %)≤ 60 min
Insolubles≤ 0.2 %
Particle size≥ 90 % between 0.15 and 1.0 mm

Drinking-water grades are supplied to EN 1407 and NSF/ANSI 60. The binding specification is the one in our offer and in the Certificate of Analysis for each lot.

Physical properties

PropertyValue
Bulk density (powder)about 0.6–0.8 g/cm³
pH (0.1 % solution)about 6–9
SolubilityFully soluble in water; insoluble in most organic solvents
Solution viscosityVery high; rises with molecular weight and charge
Typical stock solution0.1–0.5 %, diluted to 0.01–0.05 % before dosing
Shelf lifePowder about 24 months; emulsion about 6–12 months

Chemical properties

APAM is a polyelectrolyte: its carboxylate groups carry negative charge that makes the chain stretch in water. See PubChem for the base polymer.

  • Flocculates by bridging; it works best on particles already destabilised by a coagulant or by lime.
  • Calcium, magnesium and high salinity shrink the chains and reduce performance, so charge is matched to the water.
  • Shear, chlorine and strong oxidants break the chains; solutions are made fresh and used within about a day.
  • The polymer itself is of low toxicity; residual acrylamide monomer is the controlled impurity.

APAM applications

Mining thickeners and tailings

Doses of about 5–50 g per tonne of solids give fast settling, clear overflow for water recycling and denser underflow for tailings storage. It is used with hydrated lime for pH control.

Water and wastewater

At about 0.1–1 mg/L after a coagulant, APAM builds larger flocs in clarifiers and improves filter runs.

Coal, sand and aggregate washing

It recovers fines and returns clear wash water to the plant.

Paper and industry

It acts as a retention and drainage aid and clarifies white water and effluent.

Oilfield

It clarifies produced water; for drilling mud use our PHPA. For sludge dewatering, cationic polyacrylamide is normally better.

Main APAM supplier countries

China is the largest producer of polyacrylamide by volume. Other major producing countries include France, the United States, Germany, South Korea and Japan, where global flocculant makers run large plants.

Polyacrylamide in Turkey

Turkey’s mining, water and ceramics industries use large volumes of flocculant, and most of it is imported and supplied through distributors and service companies. Grades are normally selected by on-site jar tests.

Mercafons supplies APAM powder and emulsion through its Istanbul office, with jar-test support and CoA for each lot.

Polyacrylamide price per ton

The polyacrylamide price depends on form, charge, molecular weight, monomer specification and order size; powder costs less per active tonne than emulsion. Request a quote with a sample of your slurry or water.

APAM packaging

Packages are marked with product, grade, lot number and net weight.

25 kg bags – Anionic Polyacrylamide (Flocculant) packaging | Mercafons
25 kg bagsPowder in 25 kg PE-lined bags; 40 bags (1 t) per pallet, stretch-wrapped.
1,000 L IBC – Anionic Polyacrylamide (Flocculant) packaging | Mercafons
1,000 L IBCEmulsion in 1,000 L IBC totes.

Shipment

APAM powder is not a dangerous good for transport; a 20 ft container holds about 20 t on pallets. Emulsion is shipped in IBCs and must be protected from freezing. See logistics. HS code: 3906.90.

Storage and safety

Storage

Keep powder dry in closed bags, away from humidity, at about 5–35 °C. Keep emulsion from frost and direct sun, and mix the IBC before use.

Safety

Spilled powder or solution makes floors extremely slippery: clean up dry, then wash. Avoid dust inhalation and eye contact; wear goggles, gloves and a dust mask.

Anionic polyacrylamide FAQ

How do I choose the right APAM grade?

By jar or cylinder tests on your own slurry or water, comparing settling speed, overflow clarity and dose. Our engineers can run them with you.

What is the difference between anionic and cationic polyacrylamide?

Anionic grades suit mineral, inorganic solids; cationic grades suit organic solids and sludge dewatering.

How do I prepare APAM solution?

Sprinkle powder slowly into the vortex of stirred water to about 0.1–0.5 %, mix gently for about 45–60 minutes, then dilute before dosing.

Is polyacrylamide safe for drinking water?

Yes, certified grades with low residual acrylamide are approved for drinking water at limited doses (EN 1407, NSF/ANSI 60).

Powder or emulsion?

Powder is cheaper and keeps longer; emulsion dissolves faster and needs simpler equipment.

APAM documents: MSDS, TDS and CoA by form

Powder and emulsion have different SDS because the emulsion contains oil and surfactants; drinking-water grades add certificates. See technical documents.

Last reviewed: November 2026