PHPADrag to rotate
Polymer segment: acrylamide / acrylateCNONaH
Industrial chemicals

PHPA Polymer

High-MW, powder or emulsion

CAS 25085-02-3HS 3906.90
Product family
Chemicals
Forms
PowderEmulsion
Packaging
25 kg bags200 L drums1,000 L IBC
Request TDS / MSDS

What is PHPA polymer?

PHPA stands for partially hydrolysed polyacrylamide, a very long, anionic copolymer of acrylamide and sodium acrylate (CAS 25085-02-3). In drilling it is the standard shale encapsulator: it wraps cuttings and the borehole wall in a polymer film that slows hydration and dispersion.

PHPA is supplied as a dry powder and as a liquid emulsion. The polymer is the same, but the forms differ in dissolving speed, handling and safety data.

Where is PHPA used?

PHPA is used in water-based muds in oil and gas, water-well, mining exploration and tunnelling. The same chemistry, sold as anionic polyacrylamide, is a flocculant in water treatment and mineral processing.

How is PHPA produced?

Acrylamide and acrylic acid (or sodium acrylate) are polymerised to molecular weights of millions; the acrylate share, about 25–35 %, gives the anionic charge.

  • Powder: gel polymerisation in water, then cutting, drying and grinding to granules.
  • Emulsion: inverse-emulsion polymerisation, with polymer droplets dispersed in mineral oil and stabilised by surfactants.
  • Each lot is checked for molecular weight, charge, residual monomer and dissolving time.

PHPA forms and grades

The table compares the two forms; each is then explained with its typical uses.

PHPA powderPHPA emulsion (liquid)
Active polymer≥ 88–90 %about 30–40 %
Dissolving30–90 min with good shearA few minutes
HandlingMixing hopper; can form fish-eyesPumped or poured directly
CarrierNoneMineral oil and surfactants
Best forLower cost per kg active, long staysFast additions, small rigs, cold weather

PHPA powder (high molecular weight)

Lowest cost per kilogram of active polymer and long shelf life. It must be added slowly through a hopper to avoid lumps.

Typical uses
  • KCl-PHPA and low-solids muds
  • Shale encapsulation
  • Clear-water drilling and solids flocculation
  • Water-well and mineral exploration drilling

PHPA liquid emulsion

Ready-to-use polymer that dissolves in minutes when sheared into water. It is easy to dose at the rig but carries oil and costs more per kilogram active.

Typical uses
  • Rapid treatments while drilling
  • Rigs without good mixing equipment
  • Coring and diamond drilling
  • Tunnelling and HDD

Molecular weight options

Higher molecular weight encapsulates more strongly; lower weight gives less viscosity and is easier to mix.

Typical uses
  • High MW: reactive shale
  • Medium or low MW: weighted muds

Typical analysis by form

ParameterPowderEmulsion
Active content≥ 88 %30–40 %
Molecular weight15–25 million10–20 million
Degree of hydrolysis (anionic)25–35 %25–35 %
Residual acrylamide≤ 0.05 %≤ 0.05 %
Water-insoluble matter≤ 0.2 %—
Dissolving time≤ 90 min≤ 10 min
AppearanceWhite granules, 20–100 meshMilky, viscous liquid

Typical values are a guide. The binding specification is the one in our offer and in the Certificate of Analysis for each lot.

Physical properties

PropertyPowderEmulsion
Bulk density / densityabout 0.6–0.8 t/m³about 1.0–1.1 g/cm³
pH (0.5 % solution)about 6–8about 6–8
SolubilityWater-solubleDisperses and inverts in water
Freezing behaviourNot affectedProtect from freezing
Temperature limit in mudabout 150 °Cabout 150 °C

Chemical properties

PHPA is an anionic polyelectrolyte. Its negative charges bind to positive sites on clay edges, which is how it encapsulates shale.

  • Sensitive to calcium and magnesium; treat hard water with soda ash before adding PHPA.
  • Works well with potassium ions, hence the common KCl-PHPA system with KCl.
  • Degraded by strong oxidisers and by heat above about 150 °C.
  • Flocculates fine drilled solids at low doses, helping solids control.

PHPA uses

Shale encapsulation

A polymer film on cuttings keeps them firm so they can be removed at the shakers instead of dispersing into the mud.

Wellbore stability

Coating the borehole wall reduces swelling and sloughing in reactive shale.

Clear-water and low-solids drilling

Small doses flocculate drilled solids so they settle in pits, keeping mud weight and solids low.

Viscosity and friction reduction

PHPA adds some viscosity and reduces friction in slim holes and coring.

Mining and tunnelling

It stabilises exploration boreholes and improves spoil handling in tunnelling slurries.

Main PHPA supplier countries

China is the largest producer of polyacrylamide by volume. France, the United States, Japan and South Korea are other major producers, including the world’s largest polyacrylamide company, based in France.

PHPA in Turkey

PHPA used in Turkey is mainly imported and is used by oil, gas, geothermal and water-well drillers, as well as mining exploration contractors. Distributors in Istanbul and other centres keep powder and emulsion grades in stock.

Mercafons supplies PHPA powder and emulsion with molecular weight and charge matched to your shale, and can supply the KCl and other polymers for a complete KCl-PHPA system.

PHPA price per ton

The PHPA price depends on form and active content: compare emulsion and powder on cost per kilogram of active polymer. Request a quote with form, molecular weight, quantity and destination.

PHPA packaging by form

All packages carry the product name, form, lot number and net weight.

25 kg bags – PHPA Polymer packaging | Mercafons
25 kg bagsPowder: multiwall paper or PE bags with liner; 40 bags per pallet.
200 L drums – PHPA Polymer packaging | Mercafons
200 L drumsEmulsion: 200 L HDPE drums, about 200 kg.
1,000 L IBC – PHPA Polymer packaging | Mercafons
1,000 L IBCEmulsion: 1,000 L IBC, about 1,000–1,050 kg.

Shipment

PHPA powder and most emulsions are not dangerous goods; check section 14 of the SDS for the specific emulsion. A 20 ft container takes about 16–18 t of powder or 18–20 t of emulsion. Protect emulsions from freezing in winter. See logistics. HS code: 3906.90.

Storage and safety

Powder

Keep dry in closed bags; shelf life is about 2 years. Moist powder lumps and dissolves poorly.

Emulsion

Store at 5–35 °C in closed containers; shelf life is about 6–12 months. Mix gently before use if layers form.

Safety for both forms

Wear goggles and gloves. Spills of powder or solution are extremely slippery: sweep up dry material and do not wash it into drains.

PHPA FAQ

Powder or emulsion PHPA: which is better?

Powder is cheaper per kilogram active; emulsion is faster and easier to mix. The choice depends on your rig’s mixing equipment and logistics.

How much PHPA is used in drilling mud?

Typically 0.25–1.5 lb/bbl of active polymer (about 0.7–4 kg/m³). Our engineers can help select molecular weight and dose.

Why does PHPA form fish-eyes?

Powder added too fast forms gel-coated lumps. Add it slowly through a hopper with high shear.

Is PHPA the same as anionic polyacrylamide?

Chemically yes. Drilling grades are chosen for encapsulation and dispersion; water-treatment grades for flocculation.

Do powder and emulsion have the same MSDS?

No. The emulsion contains mineral oil and surfactants, so it has its own SDS.

PHPA documents: MSDS, TDS and CoA by form

Powder and emulsion have different compositions, so each has its own SDS, TDS and CoA. See technical documents.

Last reviewed: November 2026