FeCl₃Drag to rotate
3D ball-and-stick modelClFe
Industrial chemicals

Ferric Chloride

Solution 40 % / anhydrous 96–98 %

CAS 7705-08-0HS 2827.39
Product family
Chemicals
Forms
Liquid 40 %Anhydrous solid
Packaging
200 L drums1,000 L IBCRoad tankerISO tank
Request TDS / MSDS

What is ferric chloride?

Ferric chloride, or iron(III) chloride (FeCl₃), CAS 7705-08-0, is an inorganic iron salt and one of the most widely used coagulants in water and wastewater treatment. It is also a strong etchant for copper.

It is supplied mainly as a dark brown ferric chloride solution 40 % and as anhydrous ferric chloride 96–98 %, a dark crystalline solid. The two forms behave very differently in handling and transport, so each is explained below.

Where is ferric chloride used?

Most ferric chloride is used in municipal and industrial water and wastewater treatment: coagulation, phosphorus removal, odour control and sludge conditioning. It is also used for printed-circuit-board etching, metal surface treatment, pigments and as a catalyst in chemical and refining processes.

How is ferric chloride produced?

Ferric chloride solution is usually made close to its users, because it is heavy and corrosive to transport.

  • From iron and hydrochloric acid: scrap iron or iron oxide reacts with hydrochloric acid to form ferrous chloride, which is then oxidised with chlorine to ferric chloride.
  • From pickling liquor: spent acid from steel pickling, rich in ferrous chloride, is purified and chlorinated, recycling a waste stream.
  • Anhydrous FeCl₃ is made by direct chlorination of iron at high temperature and collected as crystals.

Ferric chloride forms and grades

The table compares the forms; each is then explained with its typical uses.

Solution 40 %Anhydrous 96–98 %Drinking-water grade
FeCl₃38–42 %≥ 96 %Solution, low impurities
AppearanceDark brown liquidDark green-black crystalsDark brown liquid
HandlingPumped from tanksVery hygroscopic; reacts with waterPumped from tanks
Best forWater and wastewater, etchingCatalysis, synthesis, remote sitesPotable water

Ferric chloride solution 40 %

The standard form for treatment plants. It is dosed directly from storage tanks and works over a wide pH range.

Typical uses
  • Wastewater coagulation
  • Chemical phosphorus removal
  • Sewer odour and H₂S control
  • Sludge conditioning before dewatering
  • PCB and copper etching

Anhydrous ferric chloride 96–98 %

Concentrated solid with about 2.5 times more FeCl₃ per tonne than solution. It must be kept dry, because it reacts with moisture and releases heat and hydrogen chloride.

Typical uses
  • Friedel–Crafts and chlorination catalyst
  • Pigment and chemical synthesis
  • Remote sites where freight is costly
  • Dissolved on site to make solution

Drinking-water grade

Solution made from clean raw materials with strict limits on heavy metals, supplied to the EN 888 standard for potable water.

Typical uses
  • Drinking-water clarification
  • Iron coagulation before filtration
  • Arsenic and phosphate removal

Typical analysis

ParameterSolution 40 %Anhydrous
FeCl₃38–42 %≥ 96 %
Fe³⁺13.0–14.5 %≥ 33 %
Fe²⁺ (as FeCl₂)≤ 0.5 %≤ 1.0 %
Free HCl≤ 0.5 %—
Water-insoluble matter≤ 0.1 %≤ 0.5 %
Density at 20 °Cabout 1.42 g/cm³—

Drinking-water grades are supplied with heavy-metal analysis to EN 888. The binding specification is the one in our offer and in the Certificate of Analysis for each lot.

Physical properties

PropertySolution 40 %Anhydrous
AppearanceDark red-brown liquidDark green-black crystals
Molar mass (FeCl₃)162.2 g/mol162.2 g/mol
Densityabout 1.42 g/cm³about 2.90 g/cm³
Melting point—about 306 °C (decomposes)
Solubility in waterMiscibleabout 920 g/L, strongly exothermic
pHbelow 1strongly acidic in water

Chemical properties

Ferric chloride is a strong Lewis acid and hydrolyses in water. Full data is on PubChem.

  • Hydrolyses in water to form iron hydroxide flocs that trap particles and colloids.
  • Precipitates phosphate as iron phosphate and sulphide as iron sulphide.
  • Oxidises and dissolves copper, which is why it is used for etching.
  • Corrosive to most metals, including stainless steel; stains surfaces brown.

Ferric chloride uses

Wastewater coagulation

It forms heavy flocs that settle quickly, effective from pH about 4 to 11 and in cold water.

Phosphorus removal

Iron binds phosphate as insoluble iron phosphate, helping plants meet discharge limits.

Odour and sulphide control

Dosed into sewers and digesters, it binds sulphide and reduces hydrogen sulphide and corrosion.

Sludge conditioning

With hydrated lime, it conditions sludge for filter presses and centrifuges.

Etching and catalysis

The solution etches copper on circuit boards; the anhydrous salt is a catalyst in organic synthesis.

Main ferric chloride supplier countries

Because the solution is heavy and corrosive to ship, ferric chloride is mostly produced regionally. Large producers are found in Europe, the United States, China and India; anhydrous ferric chloride is traded internationally, mainly from China.

Ferric chloride in Turkey

In Turkey, ferric chloride solution is supplied by regional producers and traders to municipal and industrial treatment plants, while anhydrous grades are mostly imported.

Mercafons supplies 40 % solution in IBCs and tankers, drinking-water grade to EN 888, and anhydrous ferric chloride in drums, with transport documents for this class 8 product.

Ferric chloride price per ton

The ferric chloride price depends on form, FeCl₃ content and freight distance; for solution, freight is a large part of the cost. Compare offers per tonne of 100 % FeCl₃. Request a quote.

Ferric chloride packaging by form

All packages carry the class 8 label, UN number, lot number and net weight.

1,000 L IBC – Ferric Chloride packaging | Mercafons
1,000 L IBCSolution: 1,000 L HDPE IBC, about 1,400 kg.
Road tanker – Ferric Chloride packaging | Mercafons
Road tankerSolution: rubber-lined or FRP road tanker for bulk delivery.
ISO tank – Ferric Chloride packaging | Mercafons
ISO tankSolution: lined ISO tank for export in bulk.Photo: Gerd Fahrenhorst, CC BY 4.0, via Wikimedia Commons (brands blurred)
200 L drums – Ferric Chloride packaging | Mercafons
200 L drumsAnhydrous: sealed steel or plastic drums with liner.

Shipment by form

Both forms ship as dangerous goods under IMDG, ADR and RID. See logistics.

Solution 40 %Anhydrous
UN numberUN 2582, ferric chloride solutionUN 1773, ferric chloride, anhydrous
Class / packing group8 / III8 / III
HS code2827.392827.39
20 ft containerabout 16–20 IBCs, weight-limiteddrums, about 20–22 t

Storage and safety

Solution

Store in FRP, HDPE or rubber-lined tanks with secondary containment. Never use carbon or stainless steel, copper or aluminium.

Anhydrous

Keep drums tightly closed in a dry place; moisture causes heat and hydrogen chloride fumes.

Safety for both forms

Corrosive: causes serious eye damage and is harmful if swallowed. Wear goggles or face shield, acid-resistant gloves and clothing; rinse spills with plenty of water and neutralise with lime or soda ash.

Ferric chloride FAQ

Ferric chloride or PAC: which is better?

Ferric chloride is cheaper and better for phosphorus and sulphide removal; PAC leaves no colour and lowers pH less, so it is often preferred for drinking water.

What is the typical dose?

Usually 10–100 mg/L FeCl₃ in water and wastewater, set by jar test. Our engineers can help.

Why does ferric chloride lower pH?

Hydrolysis releases acid. In soft water, alkalinity may need to be added with lime or caustic soda.

Can I make solution from anhydrous ferric chloride?

Yes, by adding it slowly to water with cooling and fume control, since the reaction is strongly exothermic.

Do the solution and anhydrous forms have different MSDS?

Yes. They have different UN numbers and hazards, so each has its own SDS.

Ferric chloride documents: MSDS, TDS and CoA by form

Documents are issued per form, because the hazards and transport entries differ. See technical documents.

Last reviewed: November 2026