What is cationic polyacrylamide?
Cationic polyacrylamide (CPAM) is a water-soluble, high-molecular-weight copolymer of acrylamide and a quaternary ammonium monomer, most often acryloyloxyethyl trimethylammonium chloride (CAS 69418-26-4). Its positive charge binds to negatively charged organic solids such as biological sludge.
CPAM is sold by cationic charge (about 10–80 %) and molecular weight, as granular powder or liquid emulsion. The grade is chosen by jar tests or trials on the actual sludge and dewatering machine.
Where is cationic polyacrylamide used?
CPAM is the main conditioning polymer for sludge dewatering and thickening in municipal and industrial wastewater treatment. It is also used in paper making, food and beverage effluents, oily wastewater and FMCG plant effluent treatment.
How is CPAM produced?
Acrylamide is copolymerised with a cationic quaternary monomer; the ratio of the two sets the cationic charge.
- Powder: gel polymerisation in water, followed by cutting, drying and milling to granules.
- Emulsion: inverse-emulsion polymerisation, giving polymer droplets in oil that invert and dissolve in minutes in water.
- Each lot is tested for solids, charge, viscosity, dissolution time, insolubles and residual acrylamide.
CPAM grades and forms
The table compares the main grades and forms; each is then explained with its typical uses.
| Low cationic | Medium cationic | High cationic | Emulsion | |
|---|---|---|---|---|
| Cationic charge | 10–30 % | 35–55 % | 60–80 % | 20–60 % |
| Molecular weight | High | Medium to high | Medium to high | High |
| Active content | ≥ 88 % | ≥ 88 % | ≥ 88 % | about 35–50 % |
| Best for | Paper, mineral-rich sludge | Mixed municipal sludge | Biological and digested sludge | Fast make-down, small plants |
Low-cationic CPAM (10–30 %)
Suits solids with a higher inorganic content and low organic load.
- Paper retention and drainage
- Primary and industrial sludge with mineral content
- Clarification of process water
Medium-cationic CPAM (35–55 %)
The most common range for municipal plants, giving strong flocs on belt and screw presses.
- Mixed primary and secondary sludge
- Belt-press and screw-press dewatering
- Gravity-belt thickening
High-cationic CPAM (60–80 %)
High charge neutralises the strongly negative surface of fine biological solids.
- Waste activated and digested sludge
- Decanter centrifuges
- Food, dairy and brewery effluent sludge
CPAM emulsion
Liquid polymer in oil, about 35–50 % active, that dissolves in minutes in simple dosing units.
- Small and mobile dewatering units
- Plants without powder make-up
- Dissolved-air flotation (DAF)
Typical analysis (powder)
| Parameter | Typical value |
|---|---|
| Appearance | White to off-white granular powder |
| Solid content | ≥ 88 % |
| Cationic charge | 10–80 % (per grade) |
| Molecular weight | about 5–12 million g/mol |
| Residual acrylamide | ≤ 0.05 % (drinking-water grade ≤ 0.025 %) |
| Dissolution time (0.1 %) | ≤ 60 min |
| Insolubles | ≤ 0.2 % |
| Particle size | ≥ 90 % between 0.15 and 1.0 mm |
Drinking-water grades are supplied to EN 1410 and NSF/ANSI 60. The binding specification is the one in our offer and in the Certificate of Analysis for each lot.
Physical properties
| Property | Value |
|---|---|
| Bulk density (powder) | about 0.6–0.8 g/cm³ |
| pH (0.1 % solution) | about 3–6 |
| Solubility | Fully soluble in water |
| Solution viscosity | High; rises with molecular weight |
| Typical stock solution | 0.1–0.5 % |
| Shelf life | Powder about 24 months; emulsion about 6–12 months |
Chemical properties
CPAM is a cationic polyelectrolyte that works by charge neutralisation and bridging. See PubChem for the base polymer.
- Neutralises the negative charge of organic solids and bridges them into strong, shear-resistant flocs.
- The ester-type cationic groups slowly hydrolyse at pH above about 8, so solutions are best used within about a day.
- Shear, chlorine and strong oxidants break the chains.
- Cationic polymers are more harmful to fish than anionic ones, so overdosing and direct discharge must be avoided.
CPAM applications
Sludge dewatering
Typical doses of about 2–12 kg per tonne of dry solids raise cake dryness on belt presses, decanter centrifuges, screw presses and filter presses, cutting transport and disposal costs.
Sludge thickening
On gravity belts, drums and DAF units, CPAM raises sludge solids before digestion or dewatering.
Industrial effluents
Food, dairy, brewery, textile and oily wastewaters use CPAM after a coagulant such as PAC or ferric chloride.
Paper making
Low-charge grades act as retention and drainage aids.
When to choose APAM
For mineral slurries and thickeners, anionic polyacrylamide is normally the better choice.
Main CPAM supplier countries
China is the largest producer of polyacrylamide by volume. France, the United States, Germany, South Korea and Japan are other major producing countries, where global flocculant makers operate large plants.
Cationic polyacrylamide in Turkey
Turkey’s many municipal and industrial treatment plants use CPAM for dewatering; most polymer is imported and supplied through distributors and service companies after on-site trials.
Mercafons supplies CPAM powder and emulsion through its Istanbul office, with trial support and CoA for each lot.
Cationic polyacrylamide price per ton
The cationic polyacrylamide price depends on charge, molecular weight, form and order size; higher-charge grades cost more. Request a quote with your sludge type and machine.
CPAM packaging
Packages are marked with product, grade, lot number and net weight.


Shipment
CPAM powder is normally not a dangerous good for transport; a 20 ft container holds about 20 t on pallets. Emulsion travels in IBCs and must be protected from frost. See logistics. HS code: 3906.90.
Storage and safety
Storage
Keep powder dry in closed bags at about 5–35 °C, away from humidity. Protect emulsion from frost and heat and mix the IBC before use.
Safety
Spills make floors very slippery: sweep up dry first, then wash. Wear goggles, gloves and a dust mask, and keep polymer out of drains and surface water.
Cationic polyacrylamide FAQ
How do I choose the right CPAM grade?
Run jar tests on fresh sludge, then confirm on the machine by cake dryness, filtrate clarity and dose. Our engineers can support the trial.
Why is cationic polymer used for sludge?
Organic sludge particles are negatively charged; the positive polymer neutralises and binds them into strong flocs.
How long is CPAM solution stable?
Use it within about 24 hours; cationic groups hydrolyse over time, faster in alkaline water.
Belt press or centrifuge: which grade?
Centrifuges often need higher molecular weight and shear-resistant flocs; belt presses favour medium-charge, high-MW grades.
Can CPAM replace a coagulant?
In sludge dewatering it often works alone; in water clarification it is used after a coagulant.
CPAM documents: MSDS, TDS and CoA by form
Powder and emulsion have different SDS, and drinking-water grades add certificates. See technical documents.
CPAM powder
All charge grades.
CPAM emulsion
Inverse emulsion in oil.
Drinking-water grades
Low residual monomer.
Last reviewed: November 2026














