PACDrag to rotate
Highly substituted cellulose unitOCNaH
Industrial chemicals

Polyanionic Cellulose (PAC-LV / PAC-HV)

API 13A PAC-LV and PAC-HV

CAS 9004-32-4HS 3912.31
Product family
Chemicals
Forms
Standard grade
Packaging
25 kg bags
Request TDS / MSDS

What is polyanionic cellulose (PAC)?

Polyanionic cellulose (PAC) is a high-purity, highly substituted sodium carboxymethyl cellulose (CAS 9004-32-4) made for drilling fluids. Compared with standard CMC, it has a higher degree of substitution and a more even structure, so it works in salt water and at higher temperatures.

PAC is sold in two main grades: PAC-LV (low viscosity), mainly for fluid-loss control, and PAC-HV (high viscosity, also called PAC-R), for viscosity and fluid-loss control together.

Where is PAC used?

PAC is used almost entirely in water-based drilling, completion and workover fluids in oil and gas, from fresh water to saturated salt. It is also used in water-well, geothermal and HDD drilling and in some cement spacers.

How is PAC produced?

PAC is made like CMC: purified cellulose reacts with sodium hydroxide and sodium monochloroacetate. The reaction is run to a higher degree of substitution (typically ≥ 0.9) with more uniform distribution along the chain.

  • The crude polymer is washed with aqueous alcohol to remove salt and by-products, giving purity of about 95 % or more.
  • Chain length is chosen for the grade: shorter chains for PAC-LV, longer chains for PAC-HV.
  • Each lot is tested in fresh and salt water for viscosity and API filtrate before release.

PAC grades

The table compares the grades; each is then explained with its typical uses.

PAC-LVPAC-HV (PAC-R)Premium / high-purity
Viscosity addedLowHighLV or HV
Main functionFluid-loss controlViscosity + fluid lossSame, lower dose
Salt toleranceTo saturationTo saturationTo saturation
Best forWeighted and salt mudsLow-solids and KCl-polymer mudsHPHT and critical wells

PAC-LV (low viscosity)

Controls filtrate while adding little viscosity, so it suits muds that are already viscous from weighting material or drilled solids.

Typical uses
  • Weighted water-based muds
  • Saturated salt and KCl muds
  • Completion and workover fluids
  • Cement spacers

PAC-HV (regular, PAC-R)

Builds viscosity and controls fluid loss in the same product. It is the main viscosifier in low-solids polymer systems together with xanthan gum.

Typical uses
  • Low-solids non-dispersed muds
  • KCl-polymer systems with PHPA
  • Spud and top-hole mud in salt water
  • Water-well and HDD drilling

Premium high-purity grades

Higher DS and purity for lower dosage and better performance at high temperature and hardness.

Typical uses
  • High-temperature wells
  • High-calcium or magnesium brines
  • Offshore with strict dose limits

Typical analysis

ParameterPAC-LVPAC-HV
Degree of substitution≥ 0.9≥ 0.9
Purity (dry basis)≥ 96 %≥ 96 %
Apparent viscosity, 4 % salt water≤ 40 mPa·s≥ 50 mPa·s
API filtrate, 4 % salt water≤ 16 mL≤ 23 mL
Moisture≤ 10 %≤ 10 %
pH (1 % solution)6.5–8.56.5–8.5

Values are typical for tests to API Specification 13A methods in salt water. The binding values are the ones in our offer and in the Certificate of Analysis for each lot.

Physical properties

PropertyValue
AppearanceWhite to off-white free-flowing powder
Bulk densityabout 0.5–0.75 t/m³
Particle sizetypically ≥ 90 % through 60 mesh (250 µm)
SolubilitySoluble in fresh, sea and saturated salt water
Temperature limit in mudabout 150 °C

Chemical properties

PAC is an anionic cellulose ether. Its many charged groups give it strong hydration and good tolerance to dissolved salts.

  • Works in fresh water through saturated NaCl and KCl brines.
  • Tolerates moderate calcium and magnesium; very high hardness reduces performance.
  • Encapsulates clay and cuttings, which also helps shale stability.
  • Biodegradable; can be attacked by bacteria in stored mud, so a biocide may be needed.

PAC uses

Fluid-loss control

PAC plugs pores in the filter cake, giving a thin, low-permeability cake and less filtrate invading the formation.

Viscosity in low-solids muds

PAC-HV gives viscosity without adding clay, keeping solids low and rate of penetration high.

Salt and KCl muds

Unlike bentonite, PAC still works in salt water, so it is standard in KCl-polymer and saturated-salt systems.

Shale encapsulation

Adsorbing on clay surfaces, PAC slows dispersion of cuttings and supports wellbore stability.

Completion and workover

It controls fluid loss in clear brines without damaging solids.

Main PAC supplier countries

China is the largest producer of polyanionic cellulose. Finland, the Netherlands, the United States and India also make drilling-grade cellulose ethers.

Polyanionic cellulose in Turkey

PAC used in Turkey is mainly imported and is stocked in Istanbul and other trading centres for drilling contractors working in Turkey, Iraq, the Caucasus and Central Asia.

Mercafons supplies PAC-LV and PAC-HV with each lot tested in salt water to API methods, and can combine them with barite, bentonite and other mud chemicals in one shipment.

PAC price per ton

The PAC price depends on grade, purity and performance per kilogram. A premium grade that needs a lower dose can cost less per barrel of mud. Request a quote with grade, quantity and destination.

PAC packaging

Bags are palletised and shrink-wrapped, and marked with product, grade, lot number and net weight.

25 kg bags – Polyanionic Cellulose (PAC-LV / PAC-HV) packaging | Mercafons
25 kg bagsMultiwall paper or woven PP bags with PE liner; 40 bags per pallet.

Shipment

PAC is not a dangerous good. A 20 ft container usually takes about 15–18 t on pallets. See logistics. HS code: 3912.31.

Storage and safety

Storage

Keep in a cool, dry place in closed bags; moisture causes lumps. Shelf life is usually 2–3 years.

Safety

PAC is not classified as hazardous. Avoid dust clouds and ignition sources, and wear a dust mask and goggles when mixing. Wet spills are slippery.

Polyanionic cellulose FAQ

What is the difference between PAC-LV and PAC-HV?

Both reduce fluid loss. PAC-LV adds little viscosity; PAC-HV also builds viscosity.

What is the difference between PAC and CMC?

PAC has higher substitution and purity, so it works in salt water and to about 150 °C; CMC is cheaper but weaker in salt and heat.

How much PAC is used in mud?

Typically 0.5–2 lb/bbl (about 1.5–6 kg/m³), depending on grade and target filtrate. Our engineers can recommend doses.

Can PAC replace bentonite?

In low-solids polymer muds, PAC-HV with xanthan gum can replace most bentonite, especially in salt water.

Does PAC need a biocide?

In stored or slow-moving mud, yes, to prevent bacteria from breaking down the polymer.

PAC documents: MSDS, TDS and CoA by grade

PAC-LV and PAC-HV are the same substance and share one SDS; each grade has its own TDS and CoA. See technical documents.

Last reviewed: November 2026