BentDrag to rotate
Layered aluminosilicate shown as a schematic latticeSiO
Industrial chemicals

Bentonite (API 13A)

API 13A sodium montmorillonite

CAS 1302-78-9HS 2508.10
Product family
Chemicals
Forms
Standard grade
Packaging
25 kg bags50 kg bags1–1.5 t big bags
Request TDS / MSDS

What is bentonite?

Bentonite is a natural clay made mostly of the mineral montmorillonite, a layered aluminium silicate (CAS 1302-78-9). When sodium bentonite is mixed with fresh water, its thin plates absorb water, swell many times in volume and form a smooth, gel-like slurry.

This swelling gives a drilling mud its viscosity and builds a thin, low-permeability filter cake on the borehole wall. Drilling bentonite is specified by API 13A, which defines three grades: treated bentonite, non-treated bentonite and OCMA bentonite.

Where is bentonite used?

The largest single use is water-based drilling fluid in oil and gas drilling and water-well drilling. Bentonite slurries are also used in horizontal directional drilling (HDD), piling and diaphragm walls, tunnelling, foundry sand, iron-ore pelletising and sealing applications.

How is bentonite produced?

Bentonite forms from altered volcanic ash and is mined in open pits. The clay is sorted by quality, because swelling and purity vary within a deposit.

  • Natural sodium bentonite (as in Wyoming) is dried and milled, usually to about 200 mesh (75 µm).
  • Sodium-activated bentonite is made from calcium bentonite by adding 2–5 % soda ash, extruding and ageing, so that sodium replaces calcium and the clay swells.
  • Treated grades receive small amounts of polymer to raise yield, then are dried and milled.
  • Each lot is tested for viscosity, filtrate and residue before packing.

Bentonite grades

The grade decides how much viscosity and fluid-loss control you get per tonne and whether the clay will tolerate other mud additives. The table compares the main grades; each is then explained with its typical uses.

API 13A bentoniteNon-treated (NTB)OCMA gradeCivil / HDD
Polymer treatedAllowedNoAllowedSometimes
YieldHighHigh, naturalLowerHigh
Main testAPI 13A, section 9API 13A, section 10API 13A, section 11Marsh funnel, filtrate
Best forOil and gas wellsDispersed and high-temperature mudsShallow and water wellsHDD, piling, tunnels

API 13A bentonite

The standard oilfield grade. It may be polymer-treated to meet the yield and filtrate limits, and it is the default choice for spud mud and water-based systems.

Typical uses
  • Spud and top-hole mud
  • Water-based drilling fluids
  • Filter-cake building
  • Water-well drilling

Non-treated bentonite (NTB)

Natural sodium bentonite with no added polymer. Because nothing can break down with heat or react with thinners, it is preferred in dispersed muds and deeper, hotter wells.

Typical uses
  • Dispersed lignosulfonate muds
  • High-temperature wells
  • Systems with heavy thinner use

OCMA bentonite

A lower-yield grade, often activated calcium bentonite, that meets the OCMA limits in API 13A. It is economical where lower performance is acceptable.

Typical uses
  • Shallow wells
  • Water and geothermal wells
  • Cost-sensitive top-hole sections

Civil, HDD and foundry grades

Grades tested for the job rather than to API: swelling, Marsh viscosity and filtrate for slurries, or green compression strength for foundry sand.

Typical uses
  • HDD and micro-tunnelling
  • Piling and diaphragm walls
  • Foundry green sand
  • Iron-ore pellet binder

Typical analysis and API 13A limits

ParameterAPI 13A bentoniteNon-treatedOCMA grade
Viscometer reading at 600 r/min≥ 30—≥ 30
Yield point / plastic viscosity≤ 3≤ 1.5≤ 6
Filtrate volume≤ 15.0 mL≤ 12.5 mL (dispersed)≤ 16.0 mL
Residue > 75 µm≤ 4.0 %—≤ 2.5 %
Moisture≤ 10 %—≤ 13 %
Dispersed plastic viscosity—≥ 10 cP—

Non-treated bentonite is tested on a dispersed suspension, so its limits differ. Limits follow API Specification 13A. The binding values are the ones in our offer and in the Certificate of Analysis for each lot.

Physical properties

PropertyValue
AppearanceCream, grey or light green-grey powder
Specific gravityabout 2.4–2.6
Bulk densityabout 0.8–1.0 t/m³
Swelling index (sodium grades)typically ≥ 24 mL / 2 g
pH (5 % suspension)about 8.5–10.5
Particle sizeabout 200 mesh (75 µm) or finer

Chemical properties

Montmorillonite has a sheet structure with exchangeable sodium or calcium ions between the layers. Its cation exchange capacity is typically 60–100 meq/100 g.

  • Sodium bentonite swells strongly in fresh water; calcium bentonite swells far less.
  • Salt, calcium and magnesium flocculate it, so it yields poorly in seawater unless prehydrated in fresh water.
  • Forms a thixotropic gel: thin when stirred, gelled at rest, which keeps cuttings suspended.
  • Chemically inert to most mud additives; deflocculated by thinners and dispersants.

Bentonite uses

Drilling mud

Bentonite gives water-based mud its viscosity and gel strength to carry cuttings, and its filter cake controls fluid loss. It is used with PAC, CMC and weighted with barite.

HDD, piling and tunnelling

Bentonite slurry supports the bore or trench walls, carries spoil and lubricates pipe or cutter heads.

Foundry sand

As a binder in green sand moulds, bentonite gives strength and allows the sand to be reused.

Iron-ore pelletising

Small additions bind iron-ore concentrate into pellets that survive handling and firing.

Sealing and liners

Its low permeability makes bentonite useful for pond sealing, well sealing and geosynthetic clay liners.

Main bentonite supplier countries

The United States (Wyoming) is the best-known source of natural sodium bentonite. China, India, Turkey and Greece are also major producers; see the USGS clays statistics.

Bentonite in Turkey

Turkey has large bentonite deposits, including those in Ordu, Tokat, Çankırı and Edirne. Much Turkish bentonite is calcium bentonite that is sodium-activated, and it is supplied for drilling, foundry, pelletising and cat litter.

Mercafons supplies API 13A, OCMA and civil grades from Turkish producers, with lab testing to API methods before shipment.

Bentonite price per ton

The bentonite price depends on grade (API, OCMA or civil), whether it is natural or activated, packaging and freight. We quote per metric tonne on FOB, CFR or DAP terms; request a quote with grade, quantity and destination.

Bentonite packaging

Bags are palletised and stretch-wrapped, and marked with product, grade, lot number and net weight.

25 kg bags – Bentonite (API 13A) packaging | Mercafons
25 kg bagsMultiwall paper or woven PP bags; 40–50 bags per pallet.
50 kg bags – Bentonite (API 13A) packaging | Mercafons
50 kg bagsWoven PP bags with liner, common at rig sites.
1–1.5 t big bags – Bentonite (API 13A) packaging | Mercafons
1–1.5 t big bags1–1.5 t FIBC for mud plants and HDD contractors.

Shipment

Bentonite is not a dangerous good. A 20 ft container usually takes 20–24 t of bagged bentonite, subject to road weight limits. We ship from Turkey by sea and road; see logistics. HS code: 2508.10.

Storage and safety

Storage

Keep bags dry, covered and off the ground. Damp bentonite lumps and loses yield; wet spills are very slippery.

Safety

Bentonite is not classified as hazardous, but natural clay can contain crystalline silica. Avoid breathing dust: use dust extraction, P2/N95 masks and safety glasses.

Bentonite FAQ

What is the difference between API and OCMA bentonite?

Both are API 13A grades. API bentonite must give more viscosity with less filtrate per tonne; OCMA has looser limits and costs less.

Why does bentonite not yield in seawater?

Salt and calcium stop the clay plates from hydrating. Prehydrate bentonite in fresh water first, or use a salt-tolerant viscosifier.

How much bentonite is used in drilling mud?

Typically 15–30 kg/m³ (about 5–10 lb/bbl) for spud mud, adjusted by viscosity tests. Our engineers can help with formulations.

Is bentonite the same as montmorillonite?

Bentonite is the rock or clay; montmorillonite is the mineral that gives it its swelling.

Can bentonite be used for HDD?

Yes. HDD grades are chosen for fast yield, good filtrate control and pumpability, often with polymer additives.

Bentonite documents: MSDS, TDS and CoA by grade

All bentonite grades share one SDS, because the hazard comes from the clay itself. TDS and CoA are issued per grade; see technical documents.

Last reviewed: November 2026