What is an antiscalant?
An antiscalant (scale inhibitor) is a liquid chemical that stops dissolved minerals such as calcium carbonate, calcium sulphate, barium and strontium sulphate and silica from crystallising as hard scale on membranes, heat-exchanger tubes and pipes.
Antiscalants work at very low doses, typically a few mg/L, below the amount needed to bind the minerals chemically. This is called threshold inhibition. Products are blends of phosphonates and/or polymers, so there is no single CAS number.
Where are antiscalants used?
Antiscalants protect reverse-osmosis and nanofiltration membranes in water treatment and desalination, and they are core components of cooling water and boiler water programmes. They are also used in thermal desalination, oilfield water injection, mining process water and FMCG utilities.
How are antiscalants produced?
The active ingredients are made by chemical synthesis and then blended in water.
- Phosphonates such as ATMP, HEDP, PBTC and DTPMP are made from phosphorus trichloride or phosphorous acid with amines or other organic feedstocks.
- Polymers such as polyacrylates, maleic polymers and acrylic–AMPS copolymers are made by solution polymerisation.
- Actives are blended, neutralised where needed, and each lot is tested for active content, pH, density and appearance.
Antiscalant types
The table compares the main types; each is then explained with its typical uses. The exact product is selected from a feed-water analysis.
| Phosphonate-based | Polymer-based | Phosphorus-free | RO membrane grade | |
|---|---|---|---|---|
| Actives | ATMP, HEDP, PBTC, DTPMP | Polyacrylate, maleic, acrylic–AMPS | Polyaspartate, PESA | Phosphonate + polymer blends |
| Main scales | CaCO₃, CaSO₄, BaSO₄ | CaCO₃, silica, iron, phosphate | CaCO₃, CaSO₄ | CaCO₃, CaSO₄, BaSO₄, SrSO₄, silica |
| pH as supplied | about 1–3 or 7–11 | about 3–8 | about 9–11 | per product |
| Best for | Cooling, boilers, oilfield | Silica and iron, dispersion | Low-phosphorus discharge | RO, NF and desalination |
Phosphonate-based antiscalants
Strong, cost-effective inhibitors for carbonate and sulphate scales; PBTC also tolerates high hardness and chlorine.
- Open recirculating cooling towers
- Low- and medium-pressure boilers
- Oilfield water injection and squeeze treatments
Polymer-based antiscalants and dispersants
Polymers disperse fine particles and control silica, iron and calcium phosphate, often together with phosphonates.
- High-silica feed waters
- Iron and manganese dispersion
- Cooling water with phosphate programmes
Phosphorus-free (green) antiscalants
Biodegradable polymers for sites with strict phosphorus limits on brine or blowdown.
- RO concentrate discharged to sensitive waters
- Cooling blowdown under phosphorus limits
- Sugar and food evaporators
RO membrane-grade antiscalants
Concentrated blends compatible with polyamide membranes and certified for drinking water (NSF/ANSI 60).
- Brackish-water and seawater RO
- Nanofiltration
- Drinking-water and beverage-plant RO
Typical analysis (RO grade)
| Parameter | Typical value |
|---|---|
| Appearance | Clear, colourless to amber liquid |
| Active content | about 30–50 % |
| Density (20 °C) | about 1.1–1.4 g/cm³ |
| pH (neat) | per product, acidic or neutral |
| Freezing point | about −10 °C or lower |
| Solubility | Fully miscible with water |
Each product has its own TDS. The binding specification is the one in our offer and in the Certificate of Analysis for each lot.
Physical properties
| Property | Value |
|---|---|
| Form | Liquid concentrate |
| Viscosity | Low to medium; pumpable with standard dosing pumps |
| Dilution | Dosed neat or diluted with RO permeate or soft water |
| Compatibility | Check with cationic polymers and coagulants upstream |
| Shelf life | about 12–24 months in closed containers |
Chemical properties
Antiscalants adsorb onto growing crystal nuclei, distorting and dispersing them so they stay in solution. See PubChem for HEDP, a typical active.
- Threshold effect: a few mg/L can prevent scaling in water many times supersaturated.
- Crystal modification: crystals that do form are soft and do not stick to surfaces.
- Dispersion: polymers keep silt, iron and fine particles suspended.
- Overdosing or mixing with cationic polymers or iron coagulants can foul RO membranes, so doses are calculated and checked.
Antiscalant applications
RO and nanofiltration
Dosed ahead of the cartridge filters at typically about 2–5 mg/L, an antiscalant lets RO run at higher recovery with a supersaturated concentrate. It is used with SMBS for dechlorination.
Seawater and thermal desalination
It controls carbonate and sulphate scale in SWRO and in MSF and MED evaporators.
Cooling towers
Antiscalants allow more cycles of concentration, saving water and blowdown, together with corrosion inhibitors and biocides.
Boilers and evaporators
They keep heat-transfer surfaces clean in boilers, sugar evaporators and dairy plants.
Oilfield and mining
They prevent barium and calcium scales in water injection and in process-water pipelines.
Main antiscalant supplier countries
China is the largest producer of phosphonate actives such as HEDP and ATMP. Formulated RO and cooling antiscalants are made by water-treatment companies in the United States, Europe, the Middle East and Asia.
Antiscalants in Turkey
Turkey has a large base of RO plants for drinking water, industry and tourism, and many water-treatment companies formulate antiscalants, largely from imported phosphonates and polymers.
Mercafons supplies RO-grade, cooling and boiler antiscalants through its Istanbul office, with product selection from your water analysis and CoA for each lot.
Antiscalant price
The antiscalant price depends on active content, chemistry, certification and pack size; comparing cost per mg/L dosed is more useful than price per kg. Request a quote with your feed-water analysis.
Antiscalant packaging
Packages are marked with product, lot number, net weight and hazard labels where applicable.



Shipment
Neutral blends are usually not dangerous goods; some acidic blends are classified as corrosive (Class 8). Check the SDS of the specific product. A 20 ft container holds about 18–22 t in IBCs or drums. See logistics. HS code: 3824.99.
Storage and safety
Storage
Store in closed HDPE or stainless-steel containers at about 5–40 °C, out of direct sun. Avoid carbon steel for acidic grades and do not mix different products in one tank.
Safety
Acidic grades can irritate or burn eyes and skin. Wear goggles and chemical-resistant gloves, and follow the SDS of the product supplied.
Antiscalant FAQ
How is the antiscalant dose calculated?
From a full feed-water analysis and the RO design (recovery, temperature, pH), using the maker’s projection software. Our engineers can run it.
Can I use any antiscalant on RO membranes?
No. Use membrane-compatible grades; some cooling-water products contain polymers that foul RO membranes.
Do antiscalants remove existing scale?
No, they prevent new scale. Existing scale needs acid or chelating membrane cleaning.
Is antiscalant safe for drinking water?
Yes, NSF/ANSI 60-certified grades are approved for drinking-water RO at the stated maximum dose.
What is the difference between an antiscalant and a softener?
A softener removes hardness by ion exchange; an antiscalant keeps hardness in solution without removing it.
Antiscalant documents: MSDS, TDS and CoA by type
Each antiscalant has its own SDS and TDS because the actives and pH differ. See technical documents.
Phosphonate-based (acidic) blends
Cooling, boiler and oilfield grades.
Polymer and phosphorus-free blends
Neutral grades.
RO membrane grades
Membrane and drinking-water use.
Last reviewed: November 2026














