SLESDrag to rotate
Laureth-2 sulphateCOSNaH
Industrial chemicals

Sodium Lauryl Ether Sulphate (SLES)

Technical and industry grades

CAS 68585-34-2HS 3402.39
Product family
Chemicals
Forms
Paste 70 %Liquid 28 %
Packaging
200 L drums1,000 L IBC
Request TDS / MSDS

What is SLES?

SLES (sodium laureth sulfate, sodium lauryl ether sulfate, CAS 68585-34-2) is the most widely used anionic surfactant in shampoos, shower gels and dishwashing liquids. The common type has an average of 2 moles of ethylene oxide (2EO).

It is supplied as a white to pale-yellow 70 % paste or as a clear 28 % solution. It foams richly, cleans well and is milder to skin than sodium lauryl sulfate.

Where is SLES used?

SLES is the base surfactant for personal-care and household-detergent producers. It is usually combined with CAPB for mildness and foam, with LABSA in dishwashing liquids, and with glycerin in skin-care cleansers.

How is SLES produced?

SLES is made from fatty alcohol in three steps.

  • C12–C14 fatty alcohol from palm kernel or coconut oil is ethoxylated with ethylene oxide.
  • The ethoxylate is sulphated with SO₃ gas in a falling-film reactor.
  • The acid is neutralised with sodium hydroxide to give 70 % paste; 1,4-dioxane formed in sulphation is kept low by process control and stripping.
  • The paste may be diluted to 28 %; each lot is tested for active matter, salts and pH.

SLES grades

The table compares the common grades; each is then explained with its typical uses.

SLES 70 % (2EO)SLES 28 % (2EO)SLES 1EO / 3EO
Active matter68–72 %27–29 %27–70 %
FormPasteClear liquidPaste or liquid
Freight per tonne of activeLowestAbout 2.5× higherVaries
Best forLarge plants that diluteSmall plants, direct useSpecial formulations

SLES 70 %

Concentrated paste that saves freight and storage.

Typical uses
  • Shampoos and shower gels
  • Dishwashing liquids
  • Liquid laundry detergents

SLES 28 %

Ready-to-use solution that needs no dilution equipment.

Typical uses
  • Hand soap
  • Small-batch cleaners
  • Car shampoos

SLES 1EO and 3EO

1EO foams more strongly; 3EO is milder and more soluble.

Typical uses
  • High-foam cleaners
  • Baby and mild products
  • Clear formulations

Typical analysis (SLES 70 %, 2EO)

ParameterTypical value
Active matter68–72 %
Unsulphated matter≤ 3.0 %
Sodium sulfate≤ 1.5 %
pH (10 % solution)7.0–9.5
Colour (5 % active, Klett)≤ 20
1,4-Dioxane≤ 30 mg/kg, lower on request

The binding specification is the one in our offer and in the Certificate of Analysis for each lot.

Physical properties

PropertyValue
Appearance (70 %)White to pale-yellow paste
Appearance (28 %)Clear to slightly hazy liquid
Density at 20 °Cabout 1.03–1.10 g/cm³
Gel rangeabout 30–60 % active (very viscous)
SolubilitySoluble in water

Chemical properties

See PubChem for full data.

  • Between about 30 % and 60 % active it forms a stiff gel, so the paste is diluted by adding it to water with stirring.
  • Salt (NaCl) builds viscosity in finished products; the curve peaks and then falls if too much is added.
  • It hydrolyses in acid below about pH 5, especially when warm, so finished products are kept near neutral.
  • It is readily biodegradable. SLES 70 % is classified H315, H318 and H412, but it is not a dangerous good for transport.

SLES applications

Hair and body care

Primary surfactant in shampoos, shower gels, bubble baths and liquid hand soap.

Dishwashing

Foaming and grease-cutting surfactant in hand dishwashing liquids.

Laundry and cleaners

Co-surfactant in liquid detergents, all-purpose cleaners and car shampoos.

Industry

Emulsifier in emulsion polymerisation, wetting agent in textiles and foaming agent in plasterboard.

Main SLES supplier countries

SLES is produced mainly in Indonesia, Malaysia, China, India, Thailand and Western Europe, close to fatty-alcohol and ethylene-oxide supply.

SLES in Turkey

Turkey’s large detergent and personal-care industry uses SLES 70 % and 28 % from local and imported supply.

Mercafons supplies SLES 70 % and 28 % to Turkey and the region in drums and IBCs, with documents for each lot.

SLES price

The SLES price follows fatty alcohol, ethylene oxide and energy costs, concentration, packaging and freight. Request a quote.

SLES packaging

Packaging is sealed and marked with grade, lot and dates.

200 L drums – Sodium Lauryl Ether Sulphate (SLES) packaging | Mercafons
200 L drums170 kg HDPE drums for 70 % paste; 220 kg for 28 %.
1,000 L IBC – Sodium Lauryl Ether Sulphate (SLES) packaging | Mercafons
1,000 L IBCAbout 1,000 kg IBCs, mainly for 28 % solution.

Shipment

SLES is not a dangerous good. A 20 ft container holds about 13.6 t of 70 % paste in 80 drums, or about 20 t of 28 % in IBCs. Protect from frost and heat. See logistics. HS code: 3402.39.

Storage and safety

Storage

Store closed in stainless steel or HDPE at about 5–40 °C. Shelf life is typically 12 months; 28 % solution needs good hygiene to avoid microbial growth.

Safety

Causes serious eye damage and skin irritation. Wear goggles and gloves; rinse eyes immediately with water if splashed.

SLES FAQ

Should I buy SLES 70 % or 28 %?

Large plants buy 70 % to save freight and dilute it; smaller plants often prefer 28 % for direct use.

Why does SLES 70 % turn into a gel when I dilute it?

SLES forms a gel at about 30–60 % active; add the paste slowly to water while stirring, not water to paste.

What is the difference between SLES and SLS?

SLES is ethoxylated and milder to skin; SLS has no ethylene oxide and is harsher but foams strongly.

Is 1,4-dioxane controlled?

Yes, it is minimised during production and stated on the CoA; low-dioxane grades are available.

Is your SLES palm-based?

It is made from palm-kernel or coconut fatty alcohol; RSPO grades are available on request.

SLES documents: MSDS, TDS and CoA by grade

Each grade has its own specification. See technical documents.

Last reviewed: November 2026