What is a polyether polyol?
A polyether polyol is a liquid polymer with reactive hydroxyl (OH) groups, made by adding propylene oxide and ethylene oxide to a starter molecule. It is the main partner of isocyanates such as TDI and PMDI in polyurethane.
Polyols are defined by OH value (mg KOH/g), functionality and molecular weight. Low-OH, high-MW polyols give soft, flexible foam; high-OH, high-functionality polyols give rigid foam.
Where are polyether polyols used?
Polyether polyols are used in flexible foam for mattresses and furniture, moulded foam for car seats, rigid foam for panels and appliances, and coatings, adhesives, sealants and elastomers (CASE). They are petrochemical products in refining and petrochemicals and serve consumer-goods makers in FMCG.
How are polyether polyols produced?
Polyols are made by alkoxylation in pressure reactors.
- A starter such as glycerine, propylene glycol, sucrose, sorbitol or an amine sets the functionality.
- Propylene oxide, and often ethylene oxide, is added with a KOH or double-metal-cyanide (DMC) catalyst until the target molecular weight is reached.
- The catalyst is removed, an antioxidant is added and the product is stripped of volatiles.
- Each lot is tested for OH value, acid value, water, viscosity and colour.
Polyether polyol grades
The table compares the main grades; each is then explained with its typical uses.
| Flexible slabstock | High-resilience / moulded | Polymer polyol | Rigid | CASE diols | |
|---|---|---|---|---|---|
| OH value (mg KOH/g) | about 46–58 | about 26–36 | about 20–35 | about 300–500 | about 56–112 |
| Functionality | about 3 | about 3 | about 3 | about 3.5–6 | 2 |
| Viscosity (25 °C) | about 450–650 mPa·s | about 800–1,300 mPa·s | about 2,000–6,000 mPa·s | about 2,000–15,000 mPa·s | about 150–350 mPa·s |
| Best for | Mattresses, furniture | Car seats, HR foam | High-load foam | Panels, appliances | Elastomers, adhesives |
Flexible slabstock polyols
Glycerine-started triols, about 3,000–3,500 MW, for continuous foam blocks with TDI.
- Mattresses and pillows
- Upholstered furniture
- Packaging and technical foam
High-resilience and moulding polyols
Higher-MW, EO-tipped polyols with reactive primary OH groups.
- Automotive seats and headrests
- High-resilience mattress foam
- Cold-cure moulded foam
Polymer polyols (POP)
Polyols with dispersed styrene-acrylonitrile particles that raise foam hardness.
- High-load-bearing foam
- Lower-density foam with good comfort
- Moulded foam
Rigid polyols
Sucrose-, sorbitol- or amine-started polyols with high functionality, used with PMDI.
- Sandwich panels and cold stores
- Refrigerator insulation
- Spray and pipe foam
CASE diols and triols
Low-functionality PPGs (for example 1,000 and 2,000 MW).
- Polyurethane elastomers
- Adhesives and sealants
- Coatings and binders
Typical analysis (flexible slabstock polyol)
| Parameter | Typical value |
|---|---|
| Appearance | Clear, colourless to pale yellow liquid |
| OH value | 54–58 mg KOH/g |
| Acid value | ≤ 0.08 mg KOH/g |
| Water | ≤ 0.08 % |
| Viscosity (25 °C) | 450–650 mPa·s |
| Colour (APHA) | ≤ 50 |
| Potassium | ≤ 5 mg/kg |
Each grade has its own TDS. The binding specification is the one in our offer and in the Certificate of Analysis for each lot.
Physical properties
| Property | Value |
|---|---|
| Form | Clear viscous liquid (polymer polyols are milky white) |
| Density (25 °C) | about 1.01–1.10 g/cm³ |
| Flash point | above about 200 °C |
| Water uptake | Hygroscopic; absorbs moisture from air |
| Storage temperature | about 15–40 °C |
Chemical properties
See PubChem for polypropylene glycol data.
- Hydroxyl groups react with isocyanate NCO groups to form urethane links.
- Primary OH groups (from EO capping) react faster than secondary OH groups.
- Water in polyol reacts with isocyanate to CO₂, so water content is controlled closely.
- Most polyether polyols are not classified as hazardous; amine-started rigid polyols may be irritant.
Polyol applications
Flexible foam
Slabstock polyols react with TDI from toluene to make foam blocks cut into mattresses and cushions.
Moulded foam
HR polyols and polymer polyols make car seats and furniture with good comfort and durability.
Rigid insulation
Rigid polyols with PMDI make sandwich panels, refrigerator insulation and pipe foam.
CASE
Diols and triols are used for elastomers, adhesives, sealants and coatings.
Other uses
Polyethers also serve as lubricants, defoamers and hydraulic-fluid bases.
Main polyol supplier countries
China is the largest producer of polyether polyols. Other major producing countries include the United States, Germany, the Netherlands, South Korea, Saudi Arabia, Singapore and Thailand.
Polyols in Turkey
Turkey’s mattress, furniture, automotive and insulation industries use large volumes of polyols, mostly imported and also blended by local system houses.
Mercafons supplies flexible, HR, polymer, rigid and CASE polyols through its Istanbul office, in drums, IBCs, ISO tanks and flexitanks with CoA for each lot.
Polyol price per ton
The polyol price follows propylene oxide and propylene costs, grade, packaging and freight; flexitanks lower cost for large volumes. Request a quote.
Polyol packaging
Packaging is dry and marked with product, grade, lot number and net weight.




Shipment
Most polyether polyols are not dangerous goods, so flexitanks can be used for large orders. Protect from moisture and keep above about 15 °C for easy unloading. See logistics. HS code: 3907.20.
Storage and safety
Storage
Store in closed, dry containers or tanks under dry nitrogen at about 15–40 °C. Keep away from moisture, acids and isocyanates. Use within about 6–12 months.
Safety
Spills are very slippery. Wear goggles and gloves; amine-started grades may irritate eyes and skin.
Polyether polyol FAQ
What does the OH value of a polyol mean?
It measures hydroxyl content in mg KOH/g and sets how much isocyanate the polyol needs.
What is the difference between flexible and rigid polyols?
Flexible polyols have low OH value and high molecular weight; rigid polyols have high OH value and functionality.
What is a polymer polyol?
A polyol containing dispersed polymer particles that increase foam hardness.
Can polyols be shipped in flexitanks?
Yes, most non-hazardous polyols can be, after checking compatibility.
Do you supply polyol and isocyanate together?
Yes, we supply polyols with matching PMDI.
Polyol documents: MSDS, TDS and CoA by grade
Each polyol grade has its own TDS; SDS differ between standard polyether, polymer and amine-started polyols. See technical documents.
Flexible, HR and CASE polyols
Polyether polyols.
Polymer polyols
SAN dispersions.
Rigid polyols
Sucrose, sorbitol and amine starters.
Last reviewed: November 2026














