What is hematite?
Hematite is a natural iron oxide mineral, Fe₂O₃ (CAS 1317-60-8). Ground to a fine powder, it is a weighting agent for drilling and well-control fluids, with a specific gravity of at least 5.05, about 20 % heavier than barite.
Because it is denser, hematite reaches the same mud weight with fewer solids. That keeps very heavy muds pumpable and is why API 13A hematite is chosen for high-pressure wells.
Where is hematite used?
In oil and gas, hematite weights water- and oil-based drilling muds, kill fluids, completion fluids and cement slurries. Outside the oilfield, coarse hematite is used in heavy concrete, counterweights and radiation shielding.
How is hematite produced?
Drilling-grade hematite comes from high-grade iron-ore deposits.
- Ore is mined, crushed and upgraded by gravity or magnetic separation to remove silica and other light minerals.
- It is dried and ground in ball or roller mills to the particle size required by API 13A.
- Micronized hematite is ground further in air-classifying mills to a few microns, so particles stay suspended in thin fluids.
- Each lot is tested for density, soluble calcium and particle size.
Hematite grades
The table compares the grades; each is then explained with its typical uses.
| API 13A hematite | Micronized hematite | Coarse / granular | |
|---|---|---|---|
| Density | ≥ 5.05 g/cm³ | ≥ 5.0 g/cm³ | about 4.8–5.2 g/cm³ |
| Particle size | < 75 µm (API limits) | D90 about 5–15 µm | 1–10 mm |
| Abrasion | Moderate | Low | — |
| Best for | High-density drilling and kill mud | Low-sag OBM, MPD, completions | Heavy concrete, counterweights |
API 13A hematite
The standard oilfield grade. It replaces barite where mud weights above about 2.0 SG would carry too many solids, or is blended with barite to raise density.
- High-pressure drilling muds
- Kill and well-control fluids
- Heavy cement slurries
- Barite-hematite blends
Micronized hematite
Very fine particles that settle slowly and abrade less. They give low-viscosity, sag-resistant fluids for narrow pressure windows.
- Oil-based muds with low sag
- Managed-pressure drilling
- High-density completion fluids
- Coiled-tubing and slim-hole work
Coarse and granular hematite
Screened lumps and granules for applications that need mass rather than suspension.
- Heavy and radiation-shielding concrete
- Counterweights and ballast
- Dense aggregates
Typical analysis and API 13A limits
| Parameter | API 13A requirement | Typical value |
|---|---|---|
| Density | ≥ 5.05 g/cm³ | 5.05–5.20 g/cm³ |
| Water-soluble alkaline earth metals (as Ca) | ≤ 100 mg/kg | < 80 mg/kg |
| Residue > 75 µm | ≤ 1.5 % | < 1.0 % |
| Residue > 45 µm | ≤ 15 % | 8–12 % |
| Particles < 6 µm | ≤ 15 % | 8–12 % |
| Fe₂O₃ | — | ≥ 88 % |
Limits follow API Specification 13A. Micronized and coarse grades are supplied to our TDS. The binding values are in our offer and the CoA for each lot.
Physical properties
| Property | Value |
|---|---|
| Appearance | Red-brown to dark grey powder |
| Specific gravity | 5.05–5.3 |
| Mohs hardness | about 5.5–6.5 |
| Bulk density (powder) | about 2.5–2.9 t/m³ |
| Solubility in water | Insoluble |
| Melting point | about 1,565 °C (decomposes) |
Chemical properties
Hematite is a stable iron(III) oxide. Full data is on PubChem.
- Chemically inert in water- and oil-based muds.
- Partly soluble in hydrochloric acid, which helps acid clean-up of filter cake.
- Weakly magnetic; ores with magnetite are controlled so they do not disturb magnetic survey tools.
- Natural ore can contain some quartz, so dust is controlled.
Hematite uses
Weighting high-density muds
With SG ≥ 5.05, hematite reaches weights above 2.0 SG (about 17 ppg) with fewer solids than barite, keeping viscosity manageable.
Well control
Kill muds and stock weighting material on the rig use hematite where very high density is needed quickly.
Cementing
Hematite raises the density of cement slurries for high-pressure zones.
Low-sag fluids
Micronized hematite gives thin, stable fluids for managed-pressure drilling and completions.
Heavy concrete
Coarse hematite makes dense concrete for counterweights, ballast and radiation shielding.
Main hematite supplier countries
Hematite ore is mined widely, with large deposits in Australia, Brazil, India, China and South Africa. Drilling-grade hematite is milled in India, China, Norway and the Middle East.
Hematite in Turkey
Turkey mines iron ore for its steel industry, in provinces such as Sivas and Malatya. Drilling-grade hematite for the region is ground from selected high-grade ores, Turkish and imported, and tested to API 13A.
Mercafons supplies API 13A and micronized hematite from Turkey and India, and can blend deliveries with barite for operators who use both.
Hematite price per ton
The hematite price depends on grade (micronized costs more), density, origin and freight. Compare cost per barrel of mud rather than per tonne. Request a quote with grade, quantity and destination.
Hematite packaging
Bags are palletised and marked with product, grade, lot number and net weight.


Shipment
Hematite is not a dangerous good. A 20 ft container is weight-limited, usually 22–26 t. See logistics. HS code: 2601.11.
Storage and safety
Storage
Store dry and covered; damp powder cakes. Stack bags carefully: the product is heavy for its volume.
Safety
Hematite is not classified as hazardous, but natural ore may contain crystalline silica. Use dust extraction, P2/N95 masks and goggles. Iron oxide dust stains clothing and equipment.
Hematite FAQ
Hematite or barite: which should I use?
Barite is cheaper and less abrasive and covers most wells. Hematite is chosen for very high mud weights or when solids must stay low.
Is hematite abrasive?
More than barite (Mohs about 6 versus 3), which can increase wear on pumps and bits. Micronized grades abrade less.
What mud weight can hematite reach?
Above 2.0 SG (17 ppg) in practice; the limit depends on rheology and solids tolerance. Our engineers can help.
Does hematite affect MWD tools?
Hematite itself is only weakly magnetic. Magnetite impurities are controlled so surveys are not disturbed.
What is ilmenite?
Another dense weighting mineral (SG about 4.6). Hematite is denser and more common in drilling.
Hematite documents: MSDS, TDS and CoA by grade
All hematite grades are the same mineral and share one SDS. TDS and CoA are issued per grade; see technical documents.
API 13A hematite
Tested to API 13A.
Micronized and coarse grades
Supplied to our TDS.
Last reviewed: November 2026












